This is in regards to adding AT&T or Cingular Bluetooth Phone support to a Surveyor Plus data collector.
!!!Please Note this is a ONE-TIME procedure that only needs to be done One Time per data collector and it will not need
to be repeated unless the customer installs a new Operating System later or sends the unit in for Service.
***I. Setup a Bluetooth Cellphone Dial-up Icon***
This is a set of instructions for creating an internet connection through an AT&T or Cingular Bluetooth Cellphone.
Turn on the Data Collector
1) Tap Start / Settings / Connections tab / Bluetooth
Turn on BT / Make this device discoverable
tap the Devices tab / tap "Add new device"
Follow the prompts to Bond to the phone with passkeys
Check the box for "Dialup Networking" as the Service / tap FINISH
2) In the Connections Tab = tap the Connections icon
Under My ISP = tap "Add a new Modem Connection"
type in "Cingular" / pick Modem type of "Bluetooth"
tap Next / tap the Device from Step #1 / tap Next
3) Enter in the Phone Number exactly as shown below then tap Next
*99#
4) Fill out the Username and Password as shown below then tap Finish
Username = WAP@CINGULARGPRS.COM
Password = CINGULAR1
Domain = leave it blank
***II. Installing Resco Registry Editor***
1) Click the Attachment at the bottom of this article and save the 2 files "Resco_Regedit.exe" and "Cingular.reg" to
your desktop or "My Documents" folder on your computer
2) Hookup your Surveyor Plus with a USB cable to your Laptop and make sure you are Connected with ActiveSync
3) Double-click the file "Resco_Regedit.exe" that you downloaded in Step #1 / Click Run when it prompts you
4) The installation wizard for Resco Explorer 2008 will open up / click Yes
5) A screen showing a list of components will be shown = to save time UNCHECK these boxes:
"FTP Add-in"
"Resco Today Plug-in"
"Desktop Shell Extension"
6) This should leave just "Reco Explorer 2008" and "Registry Add-in for Resco" CHECKED / click Install
7) Click OK when it prompts you to Check your Mobile device / Click Finish on your computer and click X to exit out of
the registration screen
8) On the screen of the Surveyor Plus data collector tap the "Install" button on the bottom left corner to install to
the default location of "Device" / tap the "Install" button a second time then when it says Successfully Installed tap
OK in the upper right
9) Using ActiveSync on your Computer Copy the file "Cingular.reg" from your Computer into the "My Documents" folder on
the Surveyor Plus. {Cingular.reg is listed as an Attachment at the bottom of this article}
10) Tap the Start button / tap Programs / scroll down and tap "Resco Registry" / tap OK to use "Touch Optimized"
11) Tap on "HKey_CURRENT_USER" / tap "Comm" / tap "RasBook"
12) At this point you should see this folderpath in your Status Bar at the top left:
"\HKey_Current_User\Comm\RasBook”
13) Type the letter C on your keyboard and it should display a folder of Cingular (if it does not then you have not
followed Step # II above)
14) tap the Menu button in the bottom right / tap Import / tap on the file "Cingular" that we copied over in Step # 9 to
highlight it
15) It should say "Registry script file imported successfully" / tap OK / tap X in the upper right twice
16) Hold down the On_Off button for a few seconds until a Menu pops up / tap the Reset button to reboot the data
collector
17) To test our new connection go into Start / Settings / Connections tab / Connections Icon
18) Tap Manage Existing Connections / tap and HOLD "Cingular" / tap Connect
the double arrows in the upper right start moving together
Returns you to the Connections screen
Exit back out to the Today Screen
19) Tap Start / Internet Explorer {or Start / Programs / Internet Explorer} and type in google.com then hit the enter
key to see if it loads up the google webpage. If it loads a webpage like google.com or carlsonsw.com then you can tap X
in the upper right and proceed to Knowledge Base Article #472
***III. Configure SurvCE with the proper settings***
1) Use Article # 472 at the link below to enter in your SurvCE Settings
SurvCE Settings for a Bluetooth Phone
!!!Please Note if you are using Tmobile:
"Tmobile.reg" is using an APN Server of:
+CGDCONT=1,,"internet2.voicestream.com"
"Tmobile2.reg" is using the APN Server of:
+CGDCONT=1,,"epc.tmobile.com"
jg